Synergy 8078 - Jeep JK Rear LCA Skids w/ Integrated Shock Manuel d'utilisateur télécharger pdf

SYNERGY MFG. 870 INDUSTRIAL WAY, SAN LUIS OBISPO, CA (805) 242-0397

INSTALLATION INSTRUCTIONS

PPM-8078 JK RHD LOWER SHOCK MOUNT

GENERAL NOTES:

 These instructions are also available on our website at www.polyperformance.com

Check the website for any updated instructions and additional photos for

reference.

 Note: Some cutting and grinding of the factory control arm mount is required for

installation.

 Bracket is designed to be bolted on but can be welded on as well if desired.

(NOTE: If bracket is being used as a lower coil over mount, we strongly

recommend the bracket be welded on)

PARTS LIST:

 2 – PPM-8078 JK R HD LOWER SHOCK MOUNT

 2 – 1/2 -13 UNC bolt 2.75” long

 2 – 1/2 -13 UNC stover nut

 4 – 1/2” flat washers

 4 – 3/8-16 UNC bolt 1” long

 4 – 3/8-16 UNC stover nut

 8 – 3/8” flat washers

 2 – 9/16 - 12 UNC bolt 4.5” long

 2 – 9/16 - 12 UNC stover nut

 4 – 9/16” flat washers

INSTRUCTIONS:

1) Begin by removing the rear TB bolt and nut at the frame side (#2 in picture

below). This is easiest to do with the vehicle still sitting on the ground under

its own weight.

1 2 3 4 5 6 7 8

INSTALLATION INSTRUCTIONS 1

Résumé du contenu

Page 1 - INSTALLATION INSTRUCTIONS

SYNERGY MFG. 870 INDUSTRIAL WAY, SAN LUIS OBISPO, CA (805) 242-0397 INSTALLATION INSTRUCTIONS PPM-8078 JK RHD LOWER SHOCK MOUNT GENERAL NOTES:

Page 2

2) Jack the vehicle up allowing the rear suspension to hang free. Support the vehicle using jack stands and remove both rear tires.

Page 3

4) Remove sway bar link where it attaches to axle. (3) 5) Remove the lower control arm. 6) Next, cut off the stock lower shoc

Page 4

NOTE: Bracket should be 5 3/8” long from top to bottom 7) Now fitment of the new PPM-8078 JK R HD lower shock mount can begin. Sl

Page 5

8) Align the bracket so the 4.5” long 9/16” bolt provided in the kit can be slid through. Put a washer on both ends and start the stover nut. D

Page 6

10) Tighten the 9/16” control arm bolt as to not allow the bracket to move. Then tighten the 3/8” bolts on the back side of the bracket. Torque t

Page 7

11) Next, remove the 9/16” control arm bolt and reinstall lower control arm. Wait to tighten control arm bolts until vehicle is sitting on the g

Page 8

13) Note, now is a good time to cycle suspension to check for proper bump-stop spacing to ensure shock does not act as bump stop. Use the approx

Commentaires sur ces manuels

Pas de commentaire

Synergy 8078 - Jeep JK Rear LCA Skids w/ Integrated Shock Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Synergy 8078 - Jeep JK Rear LCA Skids w/ Integrated Shock . Synergy 8078 - Jeep JK Rear LCA Skids w/ Integrated Shock Mounts User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Synergy 8078 - Jeep JK Rear LCA Skids w/ Integrated Shock